• Which side will you fight for? - Join Team Toasterbot!
• High quality Ultra-cotton t-shirt.
• Available in S-XXXL and Youth S,M,L.

• Pick a side in the upcoming battle - Join Team Blenderbot!
• High quality Ultra-cotton t-shirt.
• Available in S-XXXL and Youth S,M,L.

• Show off that you use the best parts in your robots with a FingerTech Transmitter Strap!
• Metal swivle-hook clips onto any transmitter.
• 100cm length rests the transmitter at the perfect position for robot driving!
• Extra soft micro-weave material for comfort.

• Has your robot been lacking a high-current power switch?  Tired of plugging and unplugging the battery during an intense competition? 
• Our Mini Switch can be activated with the simple twist of an allen key.
• No other switch is as small, lightweight and powerful!

• Tired of removing your robot's armor after every match just so you can charge the batteries?
• This lightweight jack makes charging batteries as easy as plugging in a connector.
• Robots that draw less than 6A continuous can even use this as the main power switch!

• When you don't want to solder every wire connection, these push-wire terminal blocks are a convenient solution. 
• Easily connect and disconnect up to four 18ga wires to a common connection point.
• Includes one red and one black terminal block for positive and negative (ground) connections.

• This bearing block can be used as a motor mount for 16mm gearmotors (such as our Spark motors) or as a simple bearing block for a 3mm shaft.
• The bearing works with the Spark Motors by aligning the mounting holes to the Spark mounting holes and offers additional shaft support.

These anodized aluminum motor mounts will fit just about any small motor with mounting hole distances from 10mm - 12.5mm (0.39 - 0.49in).  Especially suited to both Gold and Silver Spark motors, they will also hold all "Mini Metal Gearmotors", small Copal motors, Maxon motors, etc.

• Seven different mounting slots will fit up to 3mm or 4-40 sized screws.
• Width: 16mm (0.63in)
• Height: 19.8mm (0.78in)
• Length: 18.6mm (0.73in)
• Thickness: 1.45mm (0.057in)
• Shaft height: A motor with 11mm hole spacing will raise the motor shaft up to 11.7mm (0.46in).
• Only 1.5grams (0.05oz) each!

These anodized aluminum motor mounts will fit just about any small motor with mounting hole distances from 10mm - 12.5mm (0.39 - 0.49in).  Especially suited to both Gold and Silver Spark motors, they will also hold all "Mini Metal Gearmotors", small Copal motors, Maxon motors, etc.

• Seven different mounting slots will fit up to 3mm or 4-40 sized screws.
• Width: 16mm (0.63in)
• Height: 19.8mm (0.78in)
• Length: 18.6mm (0.73in)
• Thickness: 1.14mm (0.045in)
• Shaft height: A motor with 11mm hole spacing will raise the motor shaft up to 11.7mm (0.46in).
• Only 1.2grams (0.04oz) each!

FingerTech's Gold Spark motors are great for hobby use and in competition robots such as mini-sumo and line following.  If your application will be close to or exceeding the torque limits listed below, check out our Silver Spark motors.

• The extra-long 3mm shaft is triple-supported internally so that wheels can be mounted directly.
• All-metal spur gear reduction gearhead mated to a Mabuchi FK-050 motor.
• 9 different gear ratios for a wide range of rpm and torque to choose from (see details).
• Only 28grams (0.99oz).

The new Silver Spark line of motors has the same 16mm diameter as the Gold Sparks, but the gears are a larger pitch. This means less worrying about stripping teeth in your bigger or heavier applications!

• Extra-long 3mm shaft for mounting wheels directly with the option to use a bearing block for support on the wheel's far side.
• Same 11mm face mount pattern as Gold Spark motors.
• All-metal spur gearhead mated to a Mabuchi FK-050 motor.
• 9 different gear ratios for a wide range of rpm and torque to choose from.  One twice as fast, and one twice as slow as the Gold Sparks!
• Weights from 28 - 32grams (0.99 - 1.13oz). (see details)

• Standard-sized servo.
• Metal gears for super high torque.
• 18kg-cm (250oz-in) @ 9V
• Only 56grams (1.98oz).

• Heavy Duty Aluminum Servo Saver
• Includes inserts for Futaba, Hitec, and JR servo splines.
• Don't let your servo's gears take all the force!  Protect them with a servo saver.

FingerTech tinyESCs pack the most power into the smallest package!  Don't sacrifice space and weight on bulky motor controllers - tinyESCs are what the champions use!
Version 2.3 now with 50% higher continuous-current capacity!  Thicker pcb traces shunt heat away from the driver chip faster - meaning you can run larger motors!

• Bi-directional brushed motor controller.
• Ultra-compact and lightweight.
• Undervoltage, overcurrent, overtemp protection.
• Internal BEC (battery eliminator circuit) provides 5V to receiver - no extra receiver battery required!
• Calibrate function allows precision driving.
• Status LEDs for both directions and calibration.
• Read the tinyESC review in SERVO Magazine!

These speed controllers are perfectly matched to our own line of Gold Spark and Silver Spark motors, Copals, Sanyos, B16s, B62s, etc.  For the short operating times of robots, anything up to 5A stall can be run by tinyESCs.

• Looking for a way to get more power from your servo?
• Want to run your robot's drive system off 11.1V or more, but the servo can't go that high?
• This voltage regulator will supply 9V from any battery up to 23V.
• 4.5A is enough to power even our strongest HXT12K metal gear servo!

Out of Stock! More expected around end of May.
• Complete Antweight Combat Robot Kit.
• Featured in the SERVO Magazine articles 'Give Yourself A Wedgie!' and 'Give Yourself A Weapon!' (Reprinted by permission of T&L Publications, Inc.)
• Includes everything you need to build one of two robots: Lifter or Clamper.

• Designed to be a competitive entry into the masters class of mini-sumo, this chassis has the ability to beat those big-wheeled servo bots every single time.
• Includes garolite chassis, steel chassis ballast, 4x Spark motors, polyurethane mini-sumo wheels, line sensors, circuit board stand-offs & screws, and a stainless steel scoop.

• Using the Cobra chassis with an existing circuit board?  You'll need a good way to mount that PCB!
• This PCB Mounting Kit makes easy work of boards with different hole layouts.

• FingerTech's Mecanum Wheels allow any robotics enthusiast to add omni-directional capabilities to their creation.

• The new upgraded version is all-metal construction for maximum strength.

• Precision engineered aluminum hubs and rubber rollers with a customizable mount for any motor shaft size between 3mm - 6mm (0.118" - 0.25").

• Set includes four competition-grade wheels (two "A" side and two "B" side), a 1/16 hex wrench, and instructions for installing and controlling the wheels.

Sold out! More expected end of May.
• The Viper kit comes with everything you need to get started in competitive robotics:
Chassis, motors, wheels, speed controllers, radio receiver, and a 6-channel transmitter.

• The Viper is quite simply the best way to get into robotics. You will not find a cheaper robot kit with this functionality and expandability anywhere else.
New! The Viper is now available with a no-radio option to save you money!

• By popular demand, we have brought our experience from molding mini-sumo wheels into larger Sumo Wheels!
• Our high-traction polyurethane is molded in four sizes around a machined and anodized aluminum hub.

• The Viper basic platform kit is a perfect base to add your own circuitry for sumo robots, line followers, maze solvers, or any of your own ideas!

• Comes with everything the from Viper R/C kit except:
Radio transmitter, receiver, R/C speed controllers.

• This custom-formed aluminum Viper chassis has plenty of strength and space for additional components and upgrades.
• 14gauge (0.064") thick, 5052 alloy Aluminum punched and formed baseplate includes mounting holes for Spark motors, power switch and lid.
• Weight: 80grams (2.82oz)

• Additional Viper Lid.
• Custom 0.040" thick vacuum-formed polycarbonate lid keeps all your wires and components inside the robot.
• These new lids are thicker than the previous 0.020" lids and will stand up to much more abuse!

• Want to be at the top of the minisumo class but your robot's wheels keep slipping?  Look no further!

• Top-quality competition wheels made from high-traction polyurethane.

• Low-Bounce, Non-Treaded Foam Tire
• 5/32" (3.97mm) fits Lite Hubs, or can be drilled up to 3/16" for other shaft sizes.
• Diameters from 1.75" - 3.0"
• Option to have Lite Hubs installed (permanently epoxied) before shipping.

• Similar to Lite Flites but not as wide.
• 1/8" (3.18mm) bores can be drilled out to 5/32" for installing Lite Hubs.
• Diameters from 1.50" - 2.25"
• Option to have Lite Hubs installed (permanently epoxied) before shipping.

• If you will be mounting your Mecanum Wheels on different robots or replace the motors and need a different shaft bore size, you will want to pick up some extra mounts.

• Bore is 3mm, can be drilled out to accommodate up to 1/4" shafts.
• Includes 6-32 setscrew
• Available in aluminum and delrin.

Discontinued - See our newly upgraded Mecanum V2 Set!

• FingerTech's Mecanum Wheels allow any robotics enthusiast to add omni-directional capabilities to their creation.

• Competition Grade set includes upgraded aluminum mounts and threaded pins with screws to hold the rollers on. No gluing is required. Adding some Loctite to the screws will reassure you that an improperly glued roller will not fall off during a competition.

• Precision engineered delrin hubs and rubber rollers attach to a customizable mount for any motor shaft size between 3mm and 1/4".

• Set includes four competition-grade wheels (two "A" side and two "B" side), hex wrenchs, and instructions for installing the wheels.

Discontinued - See our newly upgraded Mecanum V2 Set!

• FingerTech's revolutionary new Mecanum Wheels allow any robotics enthusiast to add omni-directional capabilities to their creation.

• Hobby Grade set comes with plastic motor mounts and plain steel pins. Gluing the rollers onto pins is fine for hobby use. For additional reliability, check out the Competition Grade set.

• Precision engineered delrin hubs and rubber rollers attach to a customizable mount for any motor shaft size between 3mm and 1/4".

• Set includes four hobby-grade wheels (two "A" side and two "B" side), hex wrench, and instructions for installing the wheels.

Our specialty Timing Pulleys and Belts are the perfect solution for transmitting power from motors to wheels or shafts.
While O-Rings and round belts will slip under tension, timing belts have teeth that ensure a positive lock to the pulleys.

Ten pulley sizes means there are 55 different ratio combinations to choose from!
Use with FingerTech Timing Belts, or any other 3mm pitch belt.
•S3M pitch (3mm high-torque)
•Belt Width (maximum): 4mm
•Sizes: 9 Teeth - 42 Teeth
•Bore: 3mm (9T, 15T and 16T can be drilled up to 5/32", larger pulleys can be drilled up to 1/4")

This is the specially-made pulley that is included with the "Weta" Drum Beetle Kit, available from KitBots.com.
Use it to replace damaged ones, stock up on spares, or for your own creation!

Specifications:
• 30T 3mm pitch HTD pulley
• 9.779mm (0.385") bore with no hub
• Width: 9.8mm (0.386")
• No flanges
• Two 4.5mm (0.177") mounting holes spaced 19.05mm (0.75")
• Material: 6061 aluminum
• Weight: 12g (0.42oz)

Timing pulleys and belts are the best way to transmit power from your motor to drive wheels or a spinning weapon.
While O-Rings and round belts will slip under tension, timing belts have teeth that ensure a positive lock to the pulleys.

A range of thirty-two belt sizes allows you to design your robot then pick a belt, rather than the other way around!
Use with our FingerTech S3M pulleys, or any other 3mm pitch pulley.
•S3M pitch (3mm high-torque)
•Width: 4mm
•Circumferences: 120mm (40T) - 408mm (136T).

New sizes and colors!

• Garolite makes excellent baseplate and top cover material for robot construction.  It is easily machined.
• Now available in:
- Two sheet sizes (8x10", 16x10")
- Three thicknesses (1/16", 3/32", 1/8")
- and Six colors!
 

• One pair of 3mm ID chrome steel double-sealed ball bearings.
• If you robot has to take a lot of abuse - landing hard on the wheels, etc - these 3mm ball bearings are perfect for distributing the force into the frame.
• Made to fit the shaft of Spark motors, or any other motor with a 3mm shaft.

• Includes two 2-56 Button Head Screws (length of 1/8", 3/16" or 1/4")
• Black Oxide screws are harder than Stainless Steel or Zinc Plated and the heads will not strip out as easily.
• Use for mounting Gold Spark and Silver Spark motors.
• These screws require a 0.050" hex wrench

• Includes 25pcs 4-40 Flat Head Screws (length of 1/4", 3/8" or 1/2")
• Black Oxide screws are harder than Stainless Steel or Zinc Plated and the heads will not strip out as easily.
• Use for mounting Bearing Blocks.
• These screws require a 1/16" hex wrench

• Includes 25pcs 4-40 Button Head Screws (length of 1/4", 3/8" or 1/2")
• Black Oxide screws are harder than Stainless Steel or Zinc Plated and the heads will not strip out as easily.
• Use for mounting Bearing Blocks.
• These screws require a 1/16" hex wrench

• Hex Wrench (aka Allen Key)
• Used for various screws and setscrews (see details)

• Rating: 25C Discharge, 40C Burst - Get the most from your batteries!  A higher C rating allows you to pull a higher current from the same sized pack! (300mAh are 35/70C)
• JST connector (except on 120mAh), JST-XH balance plug, and high quality 18 gauge wire.
• 120mAh packs have an "E-Flite Ultra Micro" connector.  Purchase the female connector here.
• Capacities of: 120, 180, 300, 370, and 460mAh

• Rating: 25C Discharge, 40C Burst - Get the most from your batteries!  A higher C rating allows you to pull a higher current from the same sized pack!
• JST connector, JST-XH balance plug, and high quality 18 gauge wire.
• Capacities of: 180, 370, and 460mAh.

• Rating: 20C Discharge, 30C Burst
• JST connector, JST-XH balance plug, and high quality 18 gauge wire.
• Capacities of: 360, 460, 610 and 750mAh.

• Rating: 20C Discharge, 30C Burst
• JST connector, JST-XH balance plug, and high quality 18 gauge wire.
• Capacities of: 360, 460, 610 and 750mAh.

• 2-Pin JST-style male and female connector pair.
• Wires are 20 gauge, 10cm (4in) long each end.
• High quality, high strand count silicon wire used gives higher amp throughput than standard wire of the same diameter. Connectors are plated for greater amp handling.

• 2-Pin JST-style female connector.
• Wires are 20 gauge, 10cm (4in) long.  12cm including connector housing.
• High quality, high strand count silicon wire used gives higher amp throughput than standard wire of the same diameter. Connectors are plated for greater amp handling.

• The popular T-connector design (mates with Deans Ultra plugs) eliminates the possibility of reverse polarity connections.
• Provides a secure connection for battery and motor connections on R/C vehicles.
• Very low-resistance.

The HKC6 charger/balancer features programing functionality found in more expensive chargers at a fraction of the cost.
Includes power clips and charge plugs as shown.

Microprocessor controlled
Individual cell balancing
Li-ion, LiPo and LiFe capable
Ni-Cd and NiMH capable (uses Delta-peak sensitivity)
Lead Acid capable
Store function charges/discharges to a safe storage level
Fast charge Function
Data save/load
Backlit LCD

• Clear your toolbox of all those patch cables!
• Simply plug the banana plugs into your battery charger, and your battery into one of the five output connectors.
• Choose from Servo style, Deans Ultra, JST, and 2mm and 2.5mm barrel plugs.
• Also includes a loop of wire for splicing in two of your own connectors.
• All connectors are gold plated for optimal connections.
• Comes with caps for unused connectors to prevent contact with live ends.

• 6 x E-Flight Ultra Micro charging harness.
• Banana plugs for charging, JST-X balance charge connector.
• Use for charging and balancing your Nano-Tech 2S (7.4V) 120mAh battery.
• Cut off the extra ends to use as the robot-side connectors!

• This power supply will deliver 5A and 15V constant.
• A perfect match for the HKC6 charger.

• Input: 110V-240V
• Output: 15v and up to 5A
• Includes power cord.

• These are the 9V batteries recommended for our Viper kits to provide over two hours of run time and bursts of 12A (using 2 batteries).
• Procell's (two in parallel) can run an HXT 12kg-cm servo at 1.5A continuous (while the Viper is driving continuously) for well over 15 minutes.

This HobbyKing 2.4GHz Transmitter is an excellent radio for robotics. Six channels lets you control all sorts of add-ons!
There is a knob and switch for both Channels 5 and 6. This allows you to set a motor speed or servo position, then switch it on to that preset position.

• No crystals to buy, and no need to worry about other radios interfering with your robot.
• One stick has spring return on both axes, the other has a ratchet for the up/down axis.

The HobbyKing 6-Channel 2.4GHz Receiver provides a reliable link to your robot.
• This is the V2, compatible with V2 transmitters (any sold after Oct 2010)

• Bind multiple receivers to one transmitter.

• PC cable for programming "HK-T6A" Transmitter channel variables and mixing.
• Works with Windows XP, Vista, and Windows 7.

The HobbyKing 6-Channel 2.4GHz Receiver provides a reliable link to your robot.
• This is the V1, compatible with V1 transmitters (any sold before Oct 2010)

• Comes with a satellite receiver for bots with reception troubles (a lot of metal or carbon fibre can cause this). Satellite can be unplugged to save weight!
• Bind multiple receivers to one transmitter.

Don't like "tank" steering? Need a stick free for weapon control?
The Channel Mixer combines the "left/right" (Rudder or Aileron) and "up/down" (Throttle or Elevator) channels of a single stick into two individual motor outputs.
This allows you to maneuver the robot with just one thumb, leaving the other open for weapon control.

• Compact and lightweight: 5grams (0.17oz)
• Mixing Rate: 1x1 Fixed
• Precision: 200 steps

• Lite Hubs press into Lite Flite and Lectra Lite wheels, providing a secure and very lightweight method of mounting a wheel onto a motor shaft.
• Mount wheels onto any 3mm shaft  (Can be drilled out for 1/8" motor shafts)
• A setscrew secures the hub to the shaft.  Don't ever glue your wheels to your motors again!
• Don't be intimidated by the low price - Lite Hubs are the BEST way to attach these common foam wheels to a 3mm shaft.

Shopping for family, friends and colleagues has never been easier. Take the guesswork out of gift-giving and give them the gift of choice with a gift certificate for FingerTech Robotics.

• Redeemable online for hundreds of items.
• Gift Certificates are available in any amount over $10.00
• A fast and convenient alternative to the traditional gift certificate, FingerTech electronic gift certificates make great last-minute items.
• Electronic gift code makes purchasing easy.
• To redeem your FingerTech gift certificate, enter the certificate number in the Gift Certificate/Coupon box at checkout. If the order amount exceeds the certificate amount, payment will be required to cover the remaining balance.
• Unused balance remains on your gift certificate until spent - they do not expire.
• Please note: It may take up to 24 hours for the gift code to be activated and ready for use.

This is the Performance Devices 75MHz FM Crystal Set for Hitec radios.

FEATURES: Compatible with Hitec 75MHz FM radios
High manufacturing standards insure lifetime glitch free performance

INCLUDES: One transmitter and one receiver crystal

This is the Performance Devices 75MHz FM Crystal Set for Futaba radios.

FEATURES: Compatible with Futaba 75MHz FM radios
High manufacturing standards insure lifetime glitch free performance

INCLUDES: One transmitter and one receiver crystal

This is the Performance Devices 75MHz FM Crystal Set for JR radios.

FEATURES: Compatible with JR 75MHz FM radios
High manufacturing standards insure lifetime glitch free performance

INCLUDES: One transmitter and one receiver crystal